|
(ports will not send flowcontrol to far end) 5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off Ports 5/1-4 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 5509-ER-F1> (enable) set port negotiation 5/1-4 enable Ports 5/1-4 negotiation enabled 5509-ER-F1> (enable) set port channel 5/1-4 desirable Port(s) 5/1-4 channel mode set to desirable. 5509-ER-F1> (enable) set trunk 5/1 desirable isl Port(s) 5/1 trunk mode set to desirable. Port(s) 5/1 trunk type set to isl. 5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra Port 6/1 name set. 5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20 Ports 6/2-7 name set. 5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation Ports 6/8-12 name set. 5509-ER-F1> (enable) set port speed 6/1-12 100 Ports 6/1-12 transmission speed set to 100Mbps. 5509-ER-F1> (enable) set port duplex 6/1-12 full Ports 6/1-12 set to full-duplex. 5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired Ports 6/1-12 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired Ports 6/1-12 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 5509-ER-F1> (enable) set port channel 6/1-12 off Port(s) 6/1-12 channel mode set to off. 5509-ER-F1> (enable) set trunk 6/1-12 off Port(s) 6/1-12 trunk mode set to off. 5509-ER-F1> (enable) set spantree portfast 6/1-12 enable Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution. Spantree ports 6/1-12 fast start enabled. 5509-ER-F1> (enable) set vlan 20 6/1-12 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 20 1/1-2 5/1-4 6/1-12 5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts Module name set. 5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC Ports 7/1-12 name set. 5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC Ports 7/13-48 name set. 5509-ER-F1> (enable) set port duplex 7/1-48 full Ports 7/1-48 set to full-duplex. 5509-ER-F1> (enable) set spantree portfast 7/1-48 enable Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution. Spantree ports 7/1-48 fast start enabled. 5509-ER-F1> (enable) set vlan 10 7/1-12 VLAN 10 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 10 1/1-2 5/1-4 7/1-12 5509-ER-F1> (enable) set vlan 30 7/13-48 VLAN 30 modified. VLAN (责任编辑：编程世界) |