|
请准备终端一台，用路由器中所配的Console电缆及Terminal连接器，将终端 连接到路由器的Console口；连接好电源线，检查无误后，先将终端电源打开，再将路由器电源打开，显示信息如下： System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE Copyright (c) 1986-1995 by cisco Systems 2500 processor with 2048 Kbytes of main memory F3: 3653456+93560+192532 at 0x3000060 Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3000 Software (IGS-I-L), Version 11.1(4), RELEASE SOFTWARE (fc1) Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Mon 17-Jun-96 15:45 by mkamson Image text-base: 0x0301F2B4, data-base: 0x00001000 cisco 2509 (68030) processor (revision D) with 2048K/2048K bytes of memory. Processor board ID 03843159, with hardware revision 00000000 Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 8 terminal lines. 32K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read ONLY) Notice: NVRAM invalid, possibly due to write erase. --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Would you like to enter the initial configuration dialog? [yes]: 回车 First, would you like to see the current interface summary? [yes]: 回车 Any interface listed with OK? value "NO" does not have a valid configu ration Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned NO unset up down Serial0 unassigned NO unset up down Serial1 unassigned NO unset down down Configuring global parameters: Enter host name [Router]: Router (路由器取名为Router) The enable secret is a one-way cryptographic secret used instead of the enable password when it exists. Enter enable secret: cisco (设置路由器高级口令为cisco) The enable password is used when there is no enable secret and when using older software and some boot images. Enter enable password: user (设置路由器低级口令为user Enter virtual terminal password: cisco (设置路由器虚终端口令为cisco ) Configure SNMP Network Management? [yes]: 回车 Community string [public]: 回车 Configure IP? [yes]: 回车 Configure IGRP routing? [yes]: no (不采用IGRP协议路由) Configure RIP routing? [no]: 回车 Configuring interface parameters: Configuring interface Ethernet0: Is this interface in use? [yes]: 回车 Configure IP on this interface? [yes]: 回车 IP address for this interface: 86.101.3.20 (输入本路由器局域网口IP地址) Number of bits in subnet field [0]:16 Class A network is 86.0.0.0, 16 subnet bits; mask is 255.255.255.0 Configuring interface Serial0: Is this interface in use? [yes]: 回车 Configure IP on this interface? [yes]: 回车 Configure IP unnumbered on this interface? [no]: 回车 (责任编辑：编程世界) |